- #ELO TOUCH SCREEN DRIVER WINDOWS XP UPGRADE#
- #ELO TOUCH SCREEN DRIVER WINDOWS XP SOFTWARE#
- #ELO TOUCH SCREEN DRIVER WINDOWS XP WINDOWS 7#
To confirm the monitor is supported make sure the touchscreen monitor is either an ELO 15" display or is an ICSN monitor. The table above provides guidance on which hardware was included. Please note: Some monitors of older ScanStations will not be compatible with an upgraded PC. Confirm that the touchscreen monitor in use with the ScanStation is supported by the current HP 6305 PC. For more information on determining the touchscreen in use, please see the Touchscreen compatibility section below.ĭC7700 and older: Customers with these models must purchase a new ScanStation. Customers with the TouchStone 10" touchscreen will need to purchase a new ScanStation.
#ELO TOUCH SCREEN DRIVER WINDOWS XP UPGRADE#
Customers with ICSN 10" touchscreens can choose to upgrade only the ScanStation PC component or purchase a new ScanStation. RP5700: A customer can choose to upgrade the ScanStation PC component only or purchase a new ScanStation.ĭC7800/7900: These PC models shipped with either an ICSN 10" touchscreen or a TouchStone 10" touchscreen. Increasing RAM to 4GB may address this issue and can be purchased from the ShareScan spare parts list.
#ELO TOUCH SCREEN DRIVER WINDOWS XP WINDOWS 7#
Customers with XP operating system on an existing HP 6005 can use restore media provided with the original shipment to upgrade to the Windows 7 Operating system. There may be instances when an upgrade to Windows 7 results in slower performance than previously experienced. The HP 6005 model shipped with Windows XP pre-installed along with Windows 7 restore media. HP 6005:No hardware upgrades are required. Customers with XP operating system on an existing HP 6305 can use restore media provided with the original shipment to upgrade to the Windows 7 Operating system. The HP 6305 model ships with Windows 7 pre-installed.
HP 6305: No hardware upgrades are required. TouchStone 10" requires a new ScanStation Supports ShareScan 5.0, 5.1 & 5.2 with Windows 7 New ScanStation and New PC purchases will be fulfilled with HP 6305 model.
#ELO TOUCH SCREEN DRIVER WINDOWS XP SOFTWARE#
The below table shows the ScanStation Shipping models, the shipping touchscreen models and the upgrade requirements in order to support a current shipping software version with the Windows 7 operating system. Software Upgrades can be requested for registered end user customers with a current Maintenance and Support Agreement. ShareScan for ScanStations version 5.0, 5.1 and 5.2 are supported with Windows 7 32 bit Operating System.Ĭustomers using ShareScan version 4.3.5 or earlier will be required to upgrade their existing software version to the current shipping software version when changing to a Windows 7 Operating system. However, if troubleshooting reveals the issue to be related to the Windows XP operating system, Kofax may not be able to provide a fix and may recommend upgrading the operating system to Windows 7 and the ShareScan software to 5.x. Kofax will continue to provide maintenance and support for customers with valid support contracts, including ShareScan v4.x customers, in the same manner that we do today.
See Operating System options for ScanStation Customers must verify that their ScanStation PC meets the minimum hardware requirements to support Windows 7 operating system and compatible ShareScan software. Please contact Kofax Sales for current hardware options.Īs Microsoft has ended support for Windows XP in 2014 - - many customers will be updating their legacy ScanStation PCs to Windows 7. In Mach I can click reset with the touchscreen, change screens, lots of stuff, but no script buttons.Please note: This is an archived article from 2014, and is available for reference only. Both exhibit the same behavior, strange behavior. I've tried two ELO drivers, one Windows 7 exclusive, for gestures and stuff, and a generic one for all versions of Windows, XP up. Or are there workarounds for pressing buttons with script? What am I doing wrong or what to I need to set somewhere in order to get this to work. I've seen others mention using touchscreens, including ELO touchscreens. So I'm forced to uninstall the driver and unplug the USB cable to get Mach to recognize button presses on buttons with script so I can reference. And to top that off, I can't even click Reference All or any other button with script even with the mouse. In Mach3, dev version or latest lockdown, the monitor works for seemingly everything except buttons with script, like Reference All. Installing ELO drivers, monitor works fine in Windows. I have Windows 7 32 bit, an ELO 19" touchscreen monitor connected via USB.
0 kommentar(er)
